无码中文字幕日韩专区,真人无码作爱免费视频禁hnn,中字幕视频在线永久在线,国产av无码专区亚洲av麻豆丫

Welcome to Dongguan ITA Intelligent Manufacturing Technology Co., Ltd Feedback | Product | Contact Us | Chinese |

National Advisory Hotline

+86-769-89296989

Temperature control of plastic mold processing injection molding

Plastic mold processing In the injection molding, temperature control occupies a very important part, it can decide whether the product is good or bad. If you make it to the customer, you will lose the trust and cause of the customer. The company’s losses, said to be small, it’s okay to do it again, these are not, but you have to remember that these are actually wasting the company’s resources.

1. Tube temperature: The temperature to be controlled during the injection molding process includes barrel temperature, nozzle temperature and mold temperature. The first two temperatures primarily affect the plasticization and flow of the plastic, while the latter temperature primarily affects the flow and cooling of the plastic. Each plastic has a different flow temperature. The same plastic has different flow and decomposition temperatures due to different sources or grades. This is due to the difference in average molecular weight and molecular weight distribution. Plastics are injected in different types. The plasticizing process in the machine is also different, so the temperature of the selected cylinder is also different.

2. Mouth temperature: The nozzle temperature is usually slightly lower than the temperature at the top of the barrel. This is to prevent the "flowing phenomenon" that may occur in the straight-through nozzle. The nozzle temperature should not be too low, otherwise it will cause early condensation of the melt and block the nozzle*, or affect the performance of the product due to the injection of the early aggregate into the cavity.

3. Mold temperature: The mold temperature has a great influence on the intrinsic properties and apparent quality of the product. The temperature of the mold depends on the presence or absence of crystallinity of the plastic, the size and structure of the product, performance requirements, and other process conditions (melt temperature, injection speed and injection pressure, molding cycle, etc.).


Share to:
Top phone map Home
亚洲日韩AV片在线观看| 人妻无码视频一区二区三区| 中文字幕亚洲综合小综合在线| 亚洲av超清无码不卡在线网络| 亚洲欧美日韩国产精品专区| 亚洲欧美日韩综合久久久久| 国产成人乱色伦区| 成人无码精品免费视频在线观看| 久久青青草原精品国产APP| 无码精品人妻一区二区三区老牛| 国产免费高清69式视频在线观看| 色哟哟精品视频在线观看| 国产重口老太和小伙| 双乳奶水饱满少妇视频| 少妇人妻陈艳和黑人教练| A毛片毛片看免费| 亚洲AV永久无码精品黑人| 国产精品香蕉自产拍在线观看| 无码AV一区二区三区无码| 少妇无码太爽了在线播放| 无码人妻精品一区二区三区66| 国产96色在线 | 国| 欧美精品免费观看二区| 久久精品亚洲AV久久久无码| 日韩精品视频一区二区三区| 免费午夜福利在线观看视频| 无码精品久久一区二区三区| 一女被两男吃奶玩乳尖| 国产精品久久久久久吹潮| 亚洲国产精品无码久久久高潮| 国产乱码精品一区二区三区中文| 国内精品免费久久久久电影院97| 国产香蕉一区二区三区在线视频| 日本免费一区二区三区四区五区| 午夜福利一区二区三区在线观看| 日产无人区一线二线三线观看| 日产一二三四六七区| 丰满大胸年轻继坶HD| 成人无码视频97免费| 国产欧美日韩一区二区加勒比| 亚洲另类激情综合偷自拍图|