无码中文字幕日韩专区,真人无码作爱免费视频禁hnn,中字幕视频在线永久在线,国产av无码专区亚洲av麻豆丫

Welcome to Dongguan ITA Intelligent Manufacturing Technology Co., Ltd Feedback | Product | Contact Us | Chinese |

National Advisory Hotline

+86-769-89296989

Plastic injection mold copper public and front and back mold processing method

Before writing the knife path, after the stereo picture is finished, the center of the figure should be moved to the origin of the coordinate, and the highest point is moved to Z=0. After the shrinkage rate is added, the machining can be processed, and the copper spark position can process the negative reserve.


Before processing, check whether the clamping direction of the workpiece is the same as the direction of the graphic in the computer. Whether the positioning in the mold is correct, whether the fixture interferes with the processing, and whether the direction of the front and rear molds match. Also check that the tools you are using are complete, the benchmarks in the calibration table, and so on.




Matters needing attention when processing copper:


The determination of the spark position, the general young (ie, Jing Gong) reserve is 0.05~0.15, the coarse public is 0.2~0.5, the specific spark position can be determined by the mold master.


There is no dead corner in the copper public, and it is necessary to dismantle one more.


The cutting path of the processing copper is generally: large knife (flat knife) open thick - small knife (flat knife) clear angle, light knife with ball cutter light surface.




Open the general teacher with a flat knife without a ball knife, use a knife to open the thick knife, then the shape of the light to the number, then use the large ball knife light surface, and then use the small ball knife light surface to save trouble, for some small corners The use of a knife to process the big knife can not pass the dead angle can limit the range of the knife's knife, so as not to broadcast too many empty knives.




Tonggong, especially the young male, is relatively high in precision. The tolerance is generally selected from 0.005 to 0.02 and the step is 0.05 to 0.3. When the copper is open, it is necessary to keep the position of the ball in the knife position, that is, to open the copper profile to a thick knife radius.




Tonggong also needs to be processed in the middle position, the calibration standard, and the copper work should be corrected during the spark discharge. The copper work processed by the three sides (up, down, left, and right) must have three reference faces.




Copper material is a material that is easy to process. The speed of the cutter can be faster. When the thickness is rough, the machining allowance is 0.2~0.5, depending on the size of the workpiece. The machining allowance is large. ,Improve efficiency.




The problem of roughing the front mold,


Firstly, the copper map is rotated 180o in the front view or the side view to become the front pattern. Of course, the pillow position and the PL surface are added. Where the original body is to be left in the mold, do not use the mirror method to copper. The drawing becomes a front pattern, sometimes it is wrong (when the copper figure is asymmetrical in the X direction and the Y direction). There are two difficulties in the processing of the front mold: the material is relatively hard; the front mold cannot be easily welded, and it is wrong.




When the front die is rough, the principle of using the knife is similar to that of the copper work. The big knife is rough → the small knife is thick → the big knife light knife → the small knife light knife, but the front mold should use the big knife as much as possible, not too small knife, easy to knive, the rough is usually first Use the knife handle () to open the thick, and use the round nose knife as much as possible when the light knife is used. Because the knife is large enough and powerful, when the front mold has a parting surface, it usually encounters a problem. When the light knife is used, the parting surface is touched. The machine should be quasi-numbered, and the cavity should have a machining allowance of 0.2~0.5 (leave it out for sparks). This makes it possible to correct the surface of the mold cavity to the positive direction by 0.2 to 0.5, and set the machining allowance to 0 when writing the tool path.


When the front mold is rough or light, the range of the cutter is usually limited. Remember that the range you set is the range of the tool center, not the range of the tool boundary, not the range to which the knife is machined, but the larger the tool radius.


The common method of cutting the front mold is the curved groove and the parallel light knife. When the front mold is processed, the parting surface is generally processed to a quasi-number, and the impact surface can be left with a surplus of 0.1 to prepare the mold.


Share to:
Top phone map Home
国产成人午夜福利在线观看| 国内精品乱码卡一卡2卡麻豆| 色欲色香天天天综合网WWW| 成年女人18级毛片毛片免费| 人妻网站成熟人妻VA网站| 少妇高潮喷水在线观看| 黑人大长吊大战中国人妻| 麻豆精品久久久久久久99蜜桃| 精品少妇人妻AV无码久久| 日本19禁啪啪吃奶大尺度| 中文字幕在线亚洲精品| 国产精品亚洲片在线观看不卡| 麻花传媒剧国产mv高清播放| 亚洲VA中文字幕无码| 日韩欧美一区二区三区免费观看| 欧美一区二区三区成人片在线| 2021无码最新国产在线观看| 男女18禁啪啪无遮挡| 688欧美人禽杂交狂配| 国产乱子影视频上线免费观看| 国产精品一区二区无线| 中文字幕无码精品亚洲资源网久久| 美女视频黄A视频全免费| 久久精品国产福利国产秒拍| 八区精品色欲人妻综合网| 久久99热这里只有精品国产| 成人影片麻豆国产影片免费观看| 无码超乳爆乳中文字幕| 亚洲欧美色中文字幕在线| 亚洲国产中文曰韩丝袜| 国内精品久久久久久无码不卡| 亚洲AV午夜成人无码电影| 久久精品这里热有精品| 丁香婷婷综合久久来来去| 在线观看亚洲av日韩av| 日韩欧美中文字幕看片你懂的| 日日狠狠久久偷偷色综合| 无码专区人妻系列日韩精品少妇| 国产精品久久久久精品A级| 伊人色合天天久久综合网| 成人又黄又爽又色的网站|