无码中文字幕日韩专区,真人无码作爱免费视频禁hnn,中字幕视频在线永久在线,国产av无码专区亚洲av麻豆丫

Welcome to Dongguan ITA Intelligent Manufacturing Technology Co., Ltd Feedback | Product | Contact Us | Chinese |

National Advisory Hotline

+86-769-89296989

Analysis on the cleaning method of plastic mold

Mold cleaning is a key process in mold maintenance and maintenance, and it is also a bottleneck restricting mold maintenance. Because the speed of mold manufacturing is much faster than the speed of mold cleaning, and the mold is quickly cleaned, it is ready for the next production, so the time left for mold cleaning is quite limited. How to clean the mold?


1. Standardized cleaning procedure

Systematic mold maintenance is based on maintenance requirements and consistency of maintenance operations. In order to achieve the "cost-effective" goal, cleaning molds must be careful: develop a detailed mold cleaning program. When cleaning different parts of the mold, such as internal cleaning of the press, wiping along the edge, regular cleaning, and main cleaning, the cleaning operation method is also different.


After a certain period of operation of the mold and after visual inspection of plating wear, track marks, and mold residue content in the venting and non-venting areas, the technician can determine the procedure and frequency of mold cleaning by visual inspection. Therefore, it is important to understand the cycle of safe operation of the mold and to document the observations of residue accumulation and wear inside the mold.


Based on the mold having a certain operating cycle, all molds should be accompanied by documentation of the relevant maintenance procedures and maintenance intervals. In general, controlling the internal grease level and gear broaching, sliders, internal shaft pins and bushings, and other moving parts are key to ensuring stable production. Other factors affecting production include contamination or blockage of the waterline and sprinklers, leakage of manifolds, rust and corrosion due to water leakage or condensation.


2. What level of cleaning is enough

Usually, when the molding process is completed, dirt or residue is often left on the mold, and the final cleaning requirements are different for different kinds of residues. Resins such as polyvinyl chloride produce hydrogen chloride gas, which can corrode many types of die steel. Some other residues are separated from the flame retardant and the antioxidant, which can cause corrosion to the steel. There are also some pigment colorants that can rust the steel and the rust is difficult to remove. Even ordinary sealed water, if placed on the surface of an untreated mold for a long time, will also cause damage to the mold.


Therefore, the mold should be cleaned as necessary according to the established production cycle. Each time the mold is removed from the press, it is first necessary to open the mold vents to remove all oxidized dirt and rust from the mold and non-critical areas of the stencil to prevent it from slowly corroding the steel surface and edges. In many cases, even if the cleaning is completed, some uncoated or rust-prone mold surfaces will soon appear rust again. Therefore, even if it takes a long time to brush the unprotected mold, the surface rust cannot be completely avoided.


Many molds now have "self-cleaning" vent lines that have a high gloss. By rinsing and polishing the vents to the degree of polishing of SPI#A3, or by milling or grinding, the residue is discharged to the waste area of the vent line to prevent residue from adhering to the surface of the roughing stand. . However, if the operator uses a coarse brushing pad, emery cloth, sandpaper, grindstone or a brush with nylon bristles, brass or steel to manually grind the mold, it will cause excessive cleaning of the mold.


In general, when the surface of the mold is subjected to high-pressure pulverization cleaning using hard plastics, glass beads, walnut shells, and aluminum pellets as an abrasive, if the abrasive is used too frequently or improperly used, the polishing method also causes The surface of the mold is filled with voids, and it is easy for the residue to adhere to it, resulting in more residue, abrasion, or premature rupture or burrs of the mold, which is more detrimental to the cleaning of the mold.


Therefore, by finding a cleaning device suitable for the mold and the processing process, and referring to the cleaning method and the cleaning cycle recorded in the archive document, the maintenance time can be saved, and at the same time, the wear of the mold can be effectively reduced.


Share to:
Top phone map Home
色欲麻豆国产福利精品| 国产精品国产三级国产试看| 成人午夜爽爽爽免费视频| 精品亚洲国产成人AV不卡| 99久久国产综合精品女图图等你| A级毛片免费观看网站| 日韩女同在线二区三区| 久久亚洲精品无码AV网| 久久久国产精华特点| 久久久久波多野结衣高潮| 五月激情婷婷丁香综合基地| 一本一本久久A久久综合精品蜜桃| 国精产品蘑菇一区一区有限| 少妇人妻无码专区视频免费| 99久久国语露脸精品国产| 麻豆蜜桃国产精品无码视频综艺| 好男人视频社区WWW官网| 岛国无码AV不卡一区二区| 亚洲精品国精品久久99热| 天天综合网天天综合色| 男女18禁啪啪无遮挡网站| 日日摸夜夜添夜夜添AV| 国内精品久久久久影院一蜜桃| 亚洲AV无码久久精品成人| 又污又黄无遮掩的网站| 欧美精品国产综合久久| 久久见久久久国产精品蜜桃| 曰本无码不卡高清AV一二| 亚洲AV无一区二区三区| 97久久综合亚洲色hezyo| 久久精品99国产精品亚洲| 一卡二卡亚洲乱码一卡二卡| 国内精品久久久久久中文字幕| 永久黄网站色视频免费无下载| 综合欧美亚洲日本一区| 大地资源免费更新在线视频下载| 国产97色在线 | 日韩| 伊人久久五月丁香综合中文亚洲| 美女裸体自慰在线观看| 琪琪电影网午夜理论片717西瓜| 大又大粗又爽又黄少妇毛片|